No Installation Required, Instantly Prepare for the CWAP-404 exam and please click the below link to start the CWAP-404 Exam Simulator with a real CWAP-404 practice exam questions.
Use directly our on-line CWAP-404 exam dumps materials and try our Testing Engine to pass the CWAP-404 which is always updated.
You're the WLAN administrator for a large retailer based at the HQ in New York. The London-based office has been complaining about WLAN disconnections around lunch time each day. You suspect this might be interference from the staff microwave, how might you test your theory from the New York office?
Correct Answer:D
The best way to test the theory of microwave interference from the New York office is to use a remote spectrum analyzer. By placing one of the London APs into spectrum analyzer mode, you can capture and analyze the RF spectrum in the London office over lunch time. You can then look for any signs of microwave interference, such as high duty cycle, high amplitude, or frequency hopping on the 2.4 GHz band. This method does not require any physical access tothe microwave or any changes to its
frequency. References: [Wireless Analysis Professional Study Guide], Chapter 3: Spectrum Analysis, page 64
How many frames make up the Group Key Handshake excluding any Ack frames that may be required?
Correct Answer:B
The Group Key Handshake consists of two frames excluding any Ack frames that may be required. The Group Key Handshake is used to distribute and update the Group Temporal Key (GTK) for encrypting broadcast and multicast traffic. The AP initiates the Group Key Handshake by sending a Group Key Message 1 frame to a STA, which contains the new GTK and other information. The STA responds with a Group Key Message 2 frame to the AP, which confirms the receipt of the GTK and other information. After this, both the AP and the STA can use the new GTK for encryption and decryption of broadcast and multicast traffic . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 7: 802.11 Security, page 246; CWAP- 404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 7: 802.11 Security, page 247.
What interframe space would be expected between a CIS and a Data frame?
Correct Answer:D
The interframe space that would be expected between a CTS (Clear to Send) and a Data frame is SIFS (Short Interframe Space). A SIFS is the shortest interframe space that is used for high-priority transmissions, such as ACKs (Acknowledgements), CTSs, or data frames that are part of a fragmentation or aggregation process. A SIFS is a fixed value that depends on the PHY type and channel width. A CTS and a Data frame are part of a virtual carrier sense mechanism called RTS/CTS (Request to Send/Clear to Send), which is used to avoid collisions and hidden node problems in wireless transmissions. When a STA (station) wants to send a data frame, it first sends an RTS frame to the intended receiver, indicating the duration of the transmission. The receiver then responds with a CTS frame, also indicating the duration of the transmission. The other STAs in the vicinity hear either the RTS or the CTS frame and update their NAV (Network Allocation Vector) timers accordingly, deferring their access to the medium until the transmission is over. The sender then sends the data frame after waiting for a SIFS, followed by an ACK frame from the receiver after another SIFS. The other options are not correct, as they are not used between a CTS and a Data frame. A PIFS (PCF Interframe Space) is used for medium access by the PCF (Point Coordination Function), which is an optional and rarely implemented polling-based mechanism that provides contention-free service for time-sensitive traffic. An AIFS (Arbitration Interframe Space) is used for medium access by different ACs (Access Categories), which are logical queues that correspond to different QoS (Quality of Service) levels for different types of traffic. An AIFS is a variable interframe space that depends on the AIFSN (Arbitration Interframe Space Number) value of each AC. A DIFS (Distributed Interframe Space) is used for medium access by the DCF (Distributed Coordination Function), which is the default and mandatory contention-based mechanism that provides best-effort service for normal traffic. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 6: 802.11 Frame Exchanges, page 166-167; Chapter 7: QoS Analysis, page 194-195
Given: The Frame Check Sequence (FCS) is a 32 CRC used for error detection. The CRC is calculated over what?
Correct Answer:A
The CRC is calculated over the MAC Header and Frame Body only. The CRC (Cyclic Redundancy Check) is a 32-bit value that is used for error detection in wireless transmissions. The CRC is calculated over the MAC Header and Frame Body of a PSDU, which are the parts of the data unit that contain information such as source and destination addresses, frame type, frame control, sequence number, payload, etc. The CRC is appended to the end of the PSDU as a FCS (Frame Check Sequence) field. The CRC is not calculated over the PHY Header or PHY Preamble, which are parts of the PPDU that contain information such as modulation, coding, data rate, etc. The PHY Header and PHY Preamble are added or removed by the PHY layer during the conversion between PSDU and PPDU. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98
Where would you look in a packet trace file to identify the configured Minimum Basic Rate (MBR) of a BSS?
Correct Answer:A
The configured Minimum Basic Rate (MBR) of a BSS can be identified by looking at the Supported Rates and Extended Supported Rates elements in a Beacon frame. A Beacon frame is a type of management frame that is transmitted by an AP to advertise its presence and capabilities to potential clients. A Beacon frame contains various information elements (IEs) that provide details about the BSS configuration and operation. The Supported Rates andExtended Supported Rates IEs list the data rates that are supported by the AP for data transmission. The MBR is the lowest data rate among these supported rates that is required for all clients to join and communicate with the BSS. The MBR is usually marked with a flag bit in these IEs to indicate its mandatory status. The other options are not correct, as they do not exist or do not indicate the MBR of a BSS. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 123-124