In the 2.4 GHZ band, what data rate are Probe Requests usually sent at from an unassociated STA?
Correct Answer:B
In the 2.4 GHz band, probe requests are usually sent at the minimum basic rate from an unassociated STA. A probe request is a type of management frame that is transmitted by a STA to discover available BSSs in its vicinity. A probe request can be sent on one or more channels in either passive or active scanning mode. In passive scanning mode, a STA listens for beacon frames from APs on each channel. In active scanning mode, a STA sends probe requests on each channel and waits for probe responses from APs. A probe request is usually sent at the minimum basic rate, which is the lowest data rate among the supported rates that is required for all STAs to join and communicate with a BSS. The minimum basic rate can vary depending on the configuration of each BSS, but it is typically one of these values: 1 Mbps, 2 Mbps, 5.5 Mbps, or 11 Mbps in the 2.4 GHz band. The other options are not correct, as they do not reflect how probe requests are usually sent in the 2.4 GHz band. MCS 0 is a modulation and coding scheme used by 802.11n/ac devices in either band, but it is not a data rate per se. 6 Mbps is a data rate used by OFDM devices in either band, but it is not usually configured as a minimum basic rate in the 2.4 GHz band. References: [Wireless Analysis Professional Study Guide CWAP- 404], Chapter 5: 802.11 MAC Sublayer, page 123-124
A client is operating in an unstable RF environment. Out of five data frames transmitted to the client it only receives four. The client sends a Block Ack to acknowledge the receipt of these four frames but due to frame corruption the Block Ack is not received by the AP. Which frames will be retransmitted'
Correct Answer:A
All data frames will be retransmitted in this scenario. This is because the AP uses a Block Ack (BA) mechanism to acknowledge the receipt of multiple data frames from a client in a single frame. The BA contains a bitmap that indicates which data frames were received correctly and which were not. If the BA is not received by the AP due to frame corruption, the AP will assume that none of the data frames were received by the client and will retransmit all of them. The other options are not correct, as they do not account for the loss of the BA or the use of the bitmap. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 6: 802.11 Frame Exchanges, page 167-168
A PHY Header is added to the PSDU at which layer?
Correct Answer:C
A PHY header is added to the PSDU at the PHY layer. A PHY header is a part of the PPDU that contains information such as modulation, coding, and data rate. The PHY header is added by the PHY layer when it converts a PSDU to a PPDU for transmission, or removed by the PHY layer when it converts a PPDU to a PSDU for reception. The other layers do not add or remove a PHY header. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98
What is the difference between a Data frame and a QoS-Data frame?
Correct Answer:D
The difference between a Data frame and a QoS-Data frame is that QoS Data frames include a QoS control field. A Data frame is a type of data frame that is used to carry user data or upper layer protocol data between STAs and APs. A QoS Data frame is a type of data frame that is used to carry user data or upper layer protocol data between STAs and APs that support QoS (Quality of Service) features. QoS features allow different types of traffic to be prioritized and handled differently according to their QoS requirements, such as delay, jitter, throughput, etc. QoS Data frames include a QoS control field in their MAC header, which contains information such as traffic identifier (TID), queue size (TXOP), acknowledgment policy (ACK), etc., that are used for QoS purposes. The other options are not correct, as they do not describe the difference between Data and QoS Data frames. QoS Data frames do not include a DSCP (Differentiated Services Code Point) control field, which is part of the IP header in the network layer, not the MAC header in the data link layer. QoS Data frames do not include a QoS information element (IE), which is part of some management frames that indicate QoS capabilities or parameters, not data frames. QoS Data frames do not include an 802.1Q VLAN tag, which is part of some Ethernet frames that indicate VLAN membership or priority, not wireless frames. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 118-119
Which one of the following is an advantage of using display filters that is not an advantage of capture-time filters?
Correct Answer:C
Display filters are applied after the capture is completed and they only hide the packets from view. The filtered packets are still present in the capture file and can be enabled for view later by changing or removing the display filter. This is an advantage over capture-time filters, which discard the packets that do not match the filter criteria and
cannot be recovered later34 References:
✑ CWAP-403 Study Guide, Chapter 2: Protocol Analysis, page 37
✑ CWAP-403 Objectives, Section 2.3: Apply display filters