You have installed a new 802.1 lac WLAN configured with 80 MHz channels. Users in one area are complaining about poor performance. This area is currently served by a single AP. You take a spectrum analysis capture in the poor performing area. While examining the waterfall plot you notice the airtime utilization is higher on the first 20 MHz of the 80 MHz channel when compared to the rest of the channel. What do you conclude?
Correct Answer:B
The most likely cause of higher airtime utilization on the first 20 MHz of the 80 MHz channel is non-Wi-Fi interference. Non-Wi-Fi interference can prevent an AP from using its full channel width, as it will degrade the signal quality and increase the noise floor on some parts of the channel. This will force the AP to fall back to a narrower channel
width, such as 20 MHz or 40 MHz, to maintain communication with its clients. The waterfall plot can help identify non-Wi-Fi interference by showing spikes or bursts of RF energy on specific frequencies or sub-channels. The other options are not correct, as they do not explain why only the first 20 MHz of the channel has higher airtime utilization. References: [Wireless Analysis Professional Study Guide], Chapter 3: Spectrum Analysis, page 74-75
A manufacturing facility has installed a new automation system which incorporates an 802.11 wireless network. The automation system is controlled from tablet computers connected via the WLAN. However, the automation system has not gone live due to problem with the tablets connecting to the WLAN. The WLAN vendor has been onsite to perform a survey and confirmed good primary and secondary coverage across the facility. As a CWAP you are called in to perform Spectrum Analysis to identify any interference sources. From the spectrum analysis, you did not identify any interference sources but were able to correctly identify the issue. Which of the following issues did you identify from the spectrum analysis?
Correct Answer:D
The most likely issue that can be identified from the spectrum analysis is a power mismatch between the APs and the clients. A power mismatch occurs when the APs transmit at a higher power level than the clients, or vice versa. This can cause asymmetric communication, where one side can hear the other, but not vice versa. This can result in poor performance, disconnections, or packet loss. A spectrum analysis can reveal a power mismatch by showing different signal amplitudes or RSSI values for the APs and the clients on the same channel or frequency. The other options are not correct, as they cannot be identified from the spectrum analysis alone. The tablets?? SSID, power save mode, and noise floor can be determined by using other tools or methods, such as protocol analysis, site survey, or device configuration. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 3: Spectrum Analysis, page 79-80
The PHY layer provides framing by adding a header to create what type of data unit?
Correct Answer:D
The PHY layer provides framing by adding a header to create a PPDU. A PPDU (PHY Protocol Data Unit) is the data unit that is transmitted or received over the wireless medium by the PHY layer. A PPDU consists of a PSDU (PHY Service Data Unit) and a PHY header, which contains information such as modulation, coding, and data rate. The PHY layer adds the PHY header to the PSDU to create a PPDU for transmission, or removes the PHY header from the PPDU to extract the PSDU for reception. The other options are not correct, as they are not created by adding a header at the PHY layer. An MPDU (MAC Protocol Data Unit) is created by adding a MAC header and FCS to an MSDU (MAC Service Data Unit) at the MAC layer. An MSDU is the data unit that is passed from the LLC sublayer to the MAC sublayer or vice versa. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98
What does the value of the Listen Interval field in an Association Request frame indicate?
Correct Answer:C
The value of the Listen Interval field in an Association Request frame indicates how often a STA in power save mode wakes up to listen to Beacon frames. The Listen Interval is expressed in units of Beacon Intervals (typically 100 TU or 102.4 ms). For example, if the Listen Interval is set to 10, it means that the STA will wake up every 10 Beacon Intervals (or about 1 second) to check for buffered frames at the AP. The Listen Interval is used by the AP to determine how long it can hold frames for a STA in power save mode before discarding them . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 197; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 198.
802.11k Neighbor Requests and Neighbor Reports are sent in what type of Management Frames?
Correct Answer:B
802.11k Neighbor Requests and Neighbor Reports are sent in Action frames. An Action frame is a Management frame that is used to perform various operations or functions related to the operation or maintenance of a wireless network. An Action frame consists of a Category field that indicates the type of action being performed, and a variable-length Action Details field that contains specific information related to the action. For example, an Action frame with a Category field value of 5 indicates a Radio
Measurement action, and the Action Details field may contain a Neighbor Request or a Neighbor Report subelement . References: CWAP-404 CertifiedWireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 207; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 208; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 434.