Free JN0-664 Exam Dumps

No Installation Required, Instantly Prepare for the JN0-664 exam and please click the below link to start the JN0-664 Exam Simulator with a real JN0-664 practice exam questions.
Use directly our on-line JN0-664 exam dumps materials and try our Testing Engine to pass the JN0-664 which is always updated.

Exam Code: JN0-664
Exam Title: Service Provider - Professional (JNCIP-SP)
Vendor: Juniper
Exam Questions: 65
Last Updated: December 21st,2024

Question 1

Exhibit
JN0-664 dumps exhibit
You want to use both links between R1 and R2 Because of the bandwidth difference between the two links, you must ensure that the links are used as much as possible.
Which action will accomplish this goal?

A. Define a policy to tag routes with the appropriate bandwidth community.
B. Disable multipath.
C. Ensure that the metric-out parameter on the Gigabit Ethernet interface is higher than the 10 Gigibit Ethernet interface.
D. Enable per-prefix load balancing.

Correct Answer:D
VPLS is a Layer 2 VPN technology that allows multiple sites to connect over a shared IP/MPLS network as if they were on the same LAN. VPLS tunnels can be signaled using either Label Distribution Protocol (LDP) or Border Gateway Protocol (BGP). In this question, we have two links between R1 and R2 with different bandwidths (10 Gbps and 1 Gbps). We want to use both links as much as possible for VPLS traffic. To achieve this, we need to enable per-prefix load balancing on both routers. Per-prefix load balancing is a feature that allows a router to distribute traffic across multiple equal-cost or unequal- cost paths based on the destination prefix of each packet. This improves the utilization of multiple links and provides better load sharing than per-flow load balancing, which distributes traffic based on a hash of source and destination addresses4. Per-prefix load balancing can be enabled globally or per interface using the load-balance per-packet command.
Reference: 4: https://www.cisco.com/c/en/us/support/docs/multiprotocol-label-switching-mpls/mpls/137544-technote-mpls-00.html

Question 2

Exhibit
JN0-664 dumps exhibit
Referring to the exhibit, what do the brackets [ ] in the AS path identify?

A. They identify the local AS number associated with the AS path if configured on the router, or if AS path prepending is configured
B. They identify an AS set, which are groups of AS numbers in which the order does not matter
C. They identify that the autonomous system number is incomplete and awaiting more information from the BGP protocol.
D. They identify that a BGP confederation is being used to ensure that there are no routing loops.

Correct Answer:B
The brackets [ ] in the AS path identify an AS set, which are groups of AS numbers in which the order does not matter. An AS set is used when BGP aggregates routes from different ASs into a single prefix. For example, if BGP aggregates routes 10.0.0.0/16 and 10.1.0.0/16 from AS 100 and AS 200, respectively, into a single prefix 10.0.0.0/15, then the AS path for this prefix will be [100 200]. An AS set reduces the length of the AS path and prevents routing loops.

Question 3

You are configuring a BGP signaled Layer 2 VPN across your MPLS enabled core network. Your PE-2 device connects to two sites within the s VPN
In this scenario, which statement is correct?

A. By default on PE-2, the site's local ID is automatically assigned a value of 0 and must be configured to match the total number of attached sites.
B. You must create a unique Layer 2 VPN routing instance for each site on the PE-2 device.
C. You must use separate physical interfaces to connect PE-2 to each site.
D. By default on PE-2, the remote site IDs are automatically assigned based on the order that you add the interfaces to the site configuration.

Correct Answer:D
BGP Layer 2 VPNs use BGP to distribute endpoint provisioning information and set up pseudowires between PE devices. BGP uses the Layer 2 VPN (L2VPN) Routing Information Base (RIB) to store endpoint provisioning information, which is updated each time any Layer 2 virtual forwarding instance (VFI) is configured. The prefix and path information is stored in the L2VPN database, which allows BGP to make decisions about the best path.
In BGP Layer 2 VPNs, each site has a unique site ID that identifies it within a VFI. The site ID can be manually configured or automatically assigned by the PE device. By default, the site ID is automatically assigned based on the order that you add the interfaces to the site configuration. The first interface added to a site configuration has a site ID of 1, the second interface added has a site ID of 2, and so on.
Option D is correct because by default on PE-2, the remote site IDs are automatically assigned based on the order that you add the interfaces to the site configuration. Option A is not correct because by default on PE-2, the site’s local ID is automatically assigned a value of 0 and does not need to be configured to match the total number of attached sites. Option B is not correct because you do not need to create a unique Layer 2 VPN routing instance for each site on the PE-2 device. You can create one routing instance for all sites within a VFI. Option C is not correct because you do not need to use separate physical interfaces to connect PE-2 to each site. You can use subinterfaces or service instances on a single physical interface.

Question 4

When building an interprovider VPN, you notice on the PE router that you have hidden routes which are received from your BGP peer with family inet labeled-unica3t configured.
Which parameter must you configure to solve this problem?

A. Under the family inet labeled-unicast hierarchy, add the explicit null parameter.
B. Under the protocols ospf hierarchy, add the traffic-engineering parameter.
C. Under the family inet labeled-unicast hierarchy, add the resolve-vpn parameter.
D. Under the protocols mpls hierarchy, add the traffic-engineering parameter

Correct Answer:C
The resolve-vpn parameter is a BGP option that allows a router to resolve labeled VPN-IPv4 routes using unlabeled IPv4 routes received from another BGP peer with family inet labeled-unicast configured. This option enables interprovider VPNs without requiring MPLS labels between ASBRs or using VRF tables on ASBRs. In this scenario, you need to configure the resolve-vpn parameter under [edit protocols bgp group external family inet labeled-unicast] hierarchy level on both ASBRs.

Question 5

Which two statements are correct about a sham link? (Choose two.)

A. It creates an OSPF multihop neighborship between two PE routers.
B. It creates a BGP multihop neighborship between two PE routers.
C. The PEs exchange Type 1 OSPF LSAs instead of Type 3 OSPF LSAs for the L3VPN routes
D. The PEs exchange Type 3 OSPF LSAs instead of Type 1 OSPF LSAs for the L3VPN routes.

Correct Answer:AC
A sham link is a logical link between two PE routers that belong to the same OSPF area but are connected through an L3VPN. A sham link makes the PE routers appear as if they are directly connected, and prevents OSPF from preferring an intra-area back door link over the VPN backbone. A sham link creates an OSPF multihop neighborship between the PE routers using TCP port 646. The PEs exchange Type 1 OSPF LSAs instead of Type 3 OSPF LSAs for the L3VPN routes, which allows OSPF to use the correct metric for route selection1.